nc+ seca

  • afternoon all those of you who have nc+ seca make sure you to renew before expiry date as nc+ has moved to nagravision 3 & it's none shareable i just spoken to rafal at /satsklep.pl keep that in mind

  • Am I done with mine? Just come back to my box from been away for few weeks to this


    duo2 (0100&000068/5C00/3ABD/64:A2C56B48D39BE008E2F43782E654FC05): not found (1 ms) by smart (provider expired)


    No channels clearing and no entitlements showing but I no for a fact that about 3 weeks ago my entitlements updated to sometime in March and I remember telling canthackit in a pm that my card had just updated.


    I know from this link that nc+ are slowly stopping seca cards. http://satkurier.pl/news/16239…-parowanie-kart-seca.html

  • yes they been replacing seca with nagravision cards


    my card expires next month but it shows 12/02/18, that why i ordered conax card hopefully it arrives before 12th

  • Nagravision card should still be possible to run on NC+ with the correct equipment ofcourse, that said its possible its CAK7 Pairing which will means its tits up , does anyone know which Rom/revision the new nagra card for NC+ is? and has it even been distributed yet?


    I have an old redundent conax nc card myself which defo requires an rsa key too ! so make sure your supplier sends this to you with your new card.


    In any case NC Poland is a very good package so let hope it stays for the forseeable future, who knows i may even dust some cobwebs off my own card and top it up as i still have my old config for it.

  • Tehwiz will definitely send you the rsa with your conax card well in my case they emailed it to me. Wish I had just renewed my conax card now last year instead of getting a seca one it was just cheaper to get that with full pacakage at the time than renewing my conax card.


    They have asked me send them the seca card back to check it but have said it is likely nc have stopped it.


    Not even sure if nc is planning to eventually be narga only and get rid of conax has anyone heard anything on this?

    The post was edited 2 times, last by Steve K ().

    • anyone knows the correct config nc+ conax card pcsc as this is my old nc+ config


      [reader]

      label = CYFRA

      protocol = pcsc

      device = 0

      caid = 0100

      detect = cd

      mhz = 450

      cardmhz = 450

      ident = 0100:000068

      group = 1

      emmcache = 1,1,2

      blockemm-unknown = 1

      blockemm-u = 1

      saveemm-s = 1

      saveemm-g = 1

      disablecrccws = 1

      auprovid = 000100

      is this right




      [reader]


      label = CYFRA


      protocol = PCSC


      device = 0


      rsakey =


      detect = cd


      group = 1


      emmcache = 1,3,2


      blockemm-unknown = 1


      blockemm-u = 1


      blockemm-g = 1

  • Here is the config for nc+ conax card working 100% once you have the rsa.


    [reader]


    label = smart

    protocol = pcsc

    device = 0

    caid = 0b01

    rsakey = (you will receive this from your supplier)

    detect = cd

    group = 1

    emmcache = 1,3,2

    blockemm-unknown = 1

    blockemm-u = 1

    blockemm-g = 1


    As I said to you in pm allow unique emm only to activate the card then block uq emm after activation.

  • thanks i done blockemm-u = 1 but i only have tvp channels clearing & its been tvp1 for 8hours


    Cardsystem Valid To IRD ID (nagra) Maturity Provider


    Type Caid Provid ID Class Start Date Expire Date Name

    package 0B01 000000 0000000000001010 01200000 2018-02-01 2018-02-28 0B01@000000 unknown

    package 0B01 000000 0000000000001010 01006023 2011-01-01 2011-01-31 0B01@000000 unknown

    package 0B01 000000 0000000000001050 01000001 2010-12-01 2010-12-31 0B01@000000 unknown

    package 0B01 000000 0000000000001050 01000001 2010-11-01 2010-11-30 0B01@000000 unknown

  • Full Activation of the card only takes upto 2 hours. I think you should ask your supplier to resend activation make sure you stay on TVP 1 HD for 2 hours when they send it also make sure blockemm-u = 0 is set. After 2 hours then check you are able to receive all channels you have paid for.


    Remember though to set back to blockemm-u = 1 after your package activation is successful.