OPENATV CCcAM

Hi guys

try to get ccam to run on openatv 6.1 installed 2.3.0 but no joy, does the CCcam.cfg still go in etc ?

Quote from abu baniaz

OpenATV uses /usr/keys for cam config files

Tried ftp ing the Ccam.cfg there and restart cam but no joy?

Quote from abu baniaz

You have used a question mark at the end of your sentence. Only you can answer that question.

Filename is CCcam.cfg Have you got it correct? Particularly with regards to spelling and file extension.

Which receiver is this on?

yes file name is correct and its an miracle mini hd

Quote from abu baniaz

Did you restart the cam in the softcam panel?

yes mate

can someone please look at my mg_cfg below as unable to get Cccam file to work in MGCAMD or Cccamd.

In the newcam file i have amended line with CWS =

My mcamd share works fine but unable to get my euro share to work which was working fine in VIX.

##########################

###LINUXSAT-SUPPORT.COM###

##########################

# EMM messages

# 00 don't show any EMMs (default)

# 01 show only valid EMMs

# 02 show valid and bad EMMs with complete data display

M: { 01 }

# ECM messages

# 00 don't show anything about ecm

# 01 normal mode, show pids processed, decoded ecm and cw

# 02 verbose mode, show valid and bad ECMs with data

C: { 02 }

# AU

# 00 disable, no emm pids processed

# 01 enable, emm pids always processed for soft-au and shared cards

# 02 auto, emm started only if channel cant be decoded

# 03 process emm pids for network cards update only

A: { 01 }

# key update (sum 01 or 02 with 04)

# 01 update only new keys, default setting

# 02 update all keys (used for valid PMK checking)

# 04 enable TPS au

# + tps SID, which pmt pid contains au pid

U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)

# 00 files in /var/keys

# 01 files in /tmp

T: { 00 }

# network mode, use summ for several clients

# 00 no network (default)

# 01 newcamd netclient

# 02 radegast netclient

# 04 camd3 netclient

# 08 gbox netclient

# 32 cccamd netclient, card list saved as /tmp/cccamd.info

# (ECM only, supported server version up to 2.1.1, later not work)

G: { 01 }

# network retry, use summ for several options

# 00 disable

# 01 retry every new ecm

# 02 try to connect to offline shares every Q: seconds

# 04 try to detect and fast reconnect to lost (and not used atm) server

# + XX messages number and YY seconds to reconnect

# mg will reconnect to server, if no answer to last XX ecm/keepalive or

# if no answer for last ecm or keepalive sent for YY seconds

# set to 0 to disable

N: { 07 } 5 30

# network ecm timeout in seconds

K: { 05 }

# newcamd dead routes connect retry, sec

Q: { 600 }

# network shares priority

# 00 gbox, newcamd, cccamd, radegast, camd3 (default)

# 01 camd3, radegast, cccamd, gbox, newcamd

# 02 cccamd, newcamd, camd3, gbox, radegast

P: { 00 }

# on screen display type

# 00 No OSD (default)

# 01 neutrino

# 02 enigma

# 03 relook

# + user password for http auth

O: { 00 } username password

# on screen display Options, summ of:

# 01 show emu ecm

# 02 show network shares messages

# 04 show decoding failed / fta

# 08 show emm keys update

# + web port to use for osd

S: { 03 } 80

# Log option, summ of:

# 00 off

# 01 network udp log

# 02 log to console

# 04 file, appended ! delete it by yourself, before it eat all your hdd

# + IP udp-port log-file-name

L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds

# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,

# for openbox/elanvision users with remote shares make sense to set it higher than default value,

# to not hammer cards while timeshifting or playing crypted recordings.

E: { 15 }

# cache option, summ of:

# 00 Off (default)

# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list

# 02 Ecm data cache, remember CW for (E:) time

# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart

H: { 07 }

# reread files, summ of:

# 00 No (default)

# 01 reread config file on channel change (including priority and ignore, but not replace/cache)

# 02 reread SoftCam.Key on channel change

# 04 reread SoftCam.Key if file changed

R: { 04 }

# debug, summ of

# 00 off (default)

# 01 debug ecm

# 02 debug emm

# 04 debug network ecm

# 08 debug network emm

# 16 debug network login

# 32 show mem/cpu stats every 1 min

# 64 add timestamp to log messages

D: { 00 }

# box type

# 00 autodetect, change only if you think wrong type detected.

# 01 dbox2

# 02 dreambox

# 03 triple-dragon

# 04 relook

# 05 openbox

# 06 dreambox/mips

# 08 stapi/kathrein

# 09 stapi/ipbox

# 11 stapi/openbox

B: { 06 }

# map all 180x nagra caids to 1801

# default is 01

F: { 00 }

Thanks

thanks, will try mate.

Quote from Jonnygibbo69

Hi there I’m totally new at all this I have a zgemma h2h box on virgin and I’ve got narrator on movie channels etc and some other audio issues with other channels is there an idiot guide to fix this as I’ve looked through the forums and it’s like reading a different language lol

you will to need to flash it with a new image.

Quote from Jonnygibbo69

How do I do that as I bought the box already set up etc

Thanks jonny

you may be better putting this on your box if unable to update your box via software manager, but you will need to back up your line first. -- http://www.wooshbuild.co.uk/downloads.php its very easy to install and guide you on setup.