CCcam 2.3.2 Vuplus Arm Tüm Sürümleri Buradan İndirin
CCcam 2.3.2 For Arm 4K UHD Receivers
- FurkanB
- Thread is marked as Resolved.
-
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.2 not started
cam binname must be in the start command line
check you emu config file
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.3 not started
cam binname must be in the start command line
check you emu config file
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.3 not started
cam binname must be in the start command line
check you emu config file
I think something is wrong with my openatv 6.2 image i will do fresh install and i will try again
-
Tested on openbh 4.1 and work fine thanks
-
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.2 not started
cam binname must be in the start command line
check you emu config file
hi i have replaced cccam 2.3.2 for openatv and also tested and working fine now.
-
What's the difference in procedure in installing normal cccam 2.30 on Vu+ Solo2 and installing cccam arm 2.32. When installing cccam 2.30 on Solo 2 I have only to put cline in CCcam.cfg whereas when I install cccam arm 2.32 on Uno 4K and put cline in CCcam.cfg nothing opens. Presently I have Open Blackhole 4.1 image on Uno 4K.
-
cccam 2.30 on Vu+ Solo2 and installing cccam arm 2.32
Are you using the same CCcam ipk for both receivers ?
Where are you adding the CCcam.cfg ?
-
cccam 2.30 on Vu+ Solo2 and installing cccam arm 2.32
Are you using the same CCcam ipk for both receivers ?
Where are you adding the CCcam.cfg ?
No. For the Uno 4K I'm using the first ipk in Post #1. The CCcam.cfg is in etc/.
-
For the Uno 4K I'm using the first ipk in Post #1. The CCcam.cfg is in etc
Try with the attached CCcam.cfg.
Go to CCcamInfo in a browser.
http://192.168.1.2:16001 (change 192.168.1.2 to the real ip of the uno 4k)
If there is no access to CCcamInfo its not working. Try starting it in telnet with this /usr/bin/CCcam.Arm
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.2 not started
cam binname must be in the start command line
check you emu config file
hi i have replaced cccam 2.3.2 for openatv and also tested and working fine now.
thanks FurkanB its working fine now.
have you integrated emulation to it ???
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.2 not started
cam binname must be in the start command line
check you emu config file
hi i have replaced cccam 2.3.2 for openatv and also tested and working fine now.
thanks FurkanB its working fine now.
have you integrated emulation to it ???
hi there isn't any keys included in this ipk . please send your latest SoftCam.Key, constant.cw even AutoRoll.Key file in to /usr/keys/
-
Thanks for all your help. When I was trying to do what you told me, I found that I was using a Test Line that expired long time ago. Silly me! So I put an active cline in the CCcam.cfg and changed attributes of usr/camscript/Ncam_CCcam.Arm.sh and also of usr/bin/CCcam.Arm to 755 and it's working perfectly on the Uno 4K with OBH 4.1 image.
-
-
thanks ,the installation goes well on OPENATV 6.2 image , but when i wont to start CCCam 2.3.2 in my cam manager it wont start and i have this message
CCCam 2.3.2 not started
cam binname must be in the start command line
check you emu config file
hi i have replaced cccam 2.3.2 for openatv and also tested and working fine now.
thanks FurkanB its working fine now.
have you integrated emulation to it ???
hi there isn't any keys included in this ipk . please send your latest SoftCam.Key, constant.cw even AutoRoll.Key file in to /usr/keys/
i sent SoftCam.key and constant.cw and test with a channel but not working
-
i sent SoftCam.key and constant.cw and test with a channel but not working
Did you set the paths for these files in CCcam.cfg ? Change var/keys to any folder you want..
SOFTKEY FILE : /var/keys/SoftCam.Key
STATIC CW FILE : /var/keys/constant.cw
-
TNTSAT dont work
-
i sent SoftCam.key and constant.cw and test with a channel but not working
Did you set the paths for these files in CCcam.cfg ? Change var/keys to any folder you want..
SOFTKEY FILE : /var/keys/SoftCam.Key
STATIC CW FILE : /var/keys/constant.cw
Thanks a lot for you help
i set path files in cccam.cfg too
SOFTKEY FILE : /usr/keys/SoftCam.Key
STATIC CW FILE : /usr/keys/constant.cw
my channel is working now with constant.cw file but not with SoftCam.key even with the right key in it.
-
Which cccam should be used for DM920 ? 2.3.1 or 2.3.2 and can somebody tell me which file i need to download. thank you
CCcam Support Forum
Configs, discussion, downloads and guides for CCcam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!