Can you give oscam11439 all images mips arm?
need oscam11439 all images mips arm
-
- Arm Support
- borgorosso
- Thread is marked as Resolved.
There are 22 replies in this Thread which was already clicked 2,847 times. The last Post () by supwiddiss.
-
-
Can you give oscam11439 all images mips arm?
you'll find everything here: Oscam emu 1.20-trunk ALL Images mips--arm .ipk .deb
-
Adding to this. I tried several versions of 11439 arm on my Zgemma H7. None work.
Can anyone direct me to the one that will work?
And where will the configs be after I do get it running?
Currently in /etc/tuxbox/config. -
Can anyone direct me to the one that will work?
And where will the configs be after I do get it running?Both questions depend on which image is used.
-
Can anyone direct me to the one that will work?
And where will the configs be after I do get it running?Both questions depend on which image is used.
Ahh. Currently using oscam 11438 with a bin file size of 1,984,400Kb.
oscam-1.20_svn-r11438.
Files in /etc/tuxbox/config.
Ideas? -
not oscam version, the image/firmware in use like openatv, openvix etc..
-
Can anyone direct me to the one that will work?
And where will the configs be after I do get it running?Both questions depend on which image is used.
Ahh. Currently using oscam 11438 with a bin file size of 1,984,400Kb.
oscam-1.20_svn-r11438.
Files in /etc/tuxbox/config.
Ideas?you must use oscam 11439R777 witch fixed the hash mode 20 & 21.
-
None work.
What exactly do you mean by this ?
Is it keys not working or oscam emu ?
Did you go to the oscam emu web interface to see if its running ?
-
None work.
What exactly do you mean by this ?
Is it keys not working or the actual softcam, oscam emu itself ?
Did you go to the oscam emu web interface to see if its running ?
Oh. I'm sorry. I extracted the bin. Placed a few different ones for ARM receivers in the correct place. Won't launch on the panel.
Of course I did not find an ipk which I'm accustomed to and there aren't any.
Also verified the start/stop script. It's good.
BTW, using the current 11438 I'm getting afn and the other pv channels I''m used to, no issues.
......you're just like me. need more info!! -
Which firmware/image is being used (openatv, Openvix) ?
-
Which firmware/image is being used (openatv, Openvix) ?
Oh it's OpenATV 6.2.
During the AFN hash 21 a bit ago I reflashed it. Installed the ipk, slapped in my keys and a few others a guy shared here and it worked like a charm.
I like to keep oscam updated. Not so sure if waiting for a 11439 ipk wouldn't be a wise idea.
Or if the coders here realize that receiver's like mine like ipk's.
That, and the fact that members have to learn that keys directory and config directories can change when dropping a bin file in as replacement.
I found that out fast.
....if it works, i like to break it. so i can learn how to fix it. -
Try this one m8.
-
Try this one m8.
Thank you sir. Unfortunately not working.
opkg list-installed did not show version that was running.
Renamed working oscam > oscam.bak. Same for oscam.emu file.
Installed attached ipk, rebooted.
In Oscam panel I see OSCam 11400
FIrst found keys in newly populated /usr/keys. Dropped my SoftCam.key file in.
No cw's in the panel.
Next dropped entire contents from backed up config directory (tuxbox/config) to usr/keys.
Still no cw's.
I see no readers in the webif. Am seeing upper-card Reader though.
Also even though I renamed Oscam.emu startup script I'm seeing 2 readers, oscam and OSCam 11400 running in the panel.
As they say. Back to the drawing board.Brand & Model:Zgemma H7
Chipset:Broadcom 7251s
Main Memory:221284 kB free / 1028028 kB
-
remove the following:
.emu files (softcam start scrpts) from /etc folder
oscam bin files from /usr/bin
configs from /usr/keys
Then try the above attached oscam emu again (its a new version).
-
remove the following:
.emu files (softcam start scrpts) from /etc folder
oscam bin files from /usr/bin
configs from /usr/keys
Then try the above attached oscam emu again (its a new version).
Done. Rebooted after ipk install.
Softcam panel showing OSCam.EMU 11439-r777
Not starting. no CAM 1 active.
No worries. It must be getting late over there.
But thanks! Not to be a pain.
Edit:
Oops. Didn't check permissions. Reverted to prev. ver. for the eveining.
Will let you know. Evening! -
tried "enigma2-plugin-softcams-oscam.emu-11439-r777_openatv_armv7ahf-vfp-neon.ipk" with a clean install on VU+zero 4K with OpenATV 6.2
Started it with the green button, but does not decode. when I switch to another channel, only no cam appears on softcam
-
You must restart softcam in softcam setup if you not.
-
Permissions set to 755?
Check that.
Anyone care to pipe in if it makes a difference?? -
Yes permissions set to 755 but no luck
-
Try this one m8.
Hi master G. I think I'm about ready to try this again.
I'll try your last attachment again.
On the same basic subject.
This morning I was trying to check out the news on AFN 99W.
It had been working fine. Sometimes it takes a few minutes to grab cw's and decode, otherwise no issues on ver. 11438.
After 15 or so minutes of going back and forth between channels, no decoding.
I checked my webif in the softcam keys file and noticed that it hadn't been updated (ex: P 10066 00 C5FFCAA5711330 ; added by Emu Tue Dec 4 08:40:46 2018 UA: 004E0256) in a few days.
I tried deleting older added keys from days ago in the webif then saved the file.
That did not work in webif. Deleted them through FTP and saved them. I've had to do this several times in the past because the file gets too big.
Almost immediate decoding and the softcam keys started populating again with new added keys.
So the question is. Is there a way to either occasionally delete older added keys automatically? Or to increase the maximum file size for SoftCam.keys?
OSCam-EMU Support Forum
Configs, discussion, downloads and guides for OSCam-EMU Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!