Posts by Iradj

Quote from ahmed gazye

Hi to all the team members

Spark devices Processor 7162 version 25/5/2020

The skins back In this version to the previous problem , so the picos are a problem if visible in list

33dfaf97aacf6f8cf9fba9.jpg

While the previous version was wonderful

f46790d.jpg

We hope to solve the problem

thanks & good luck to the wonderful team

Enjoy & Good luck

Display More

Hi ahmad

I had the same problem, here is my solution

Go to MENU -> SETUP -> SYSTEM -> CHANNEL SELECTION SETTINGS

On 3th page set SHOW COLUMNS to 375 pixels wide

This work for me. You can change the pixel wide as suit you.

Quote from satfoot

Using Vuplus Solo2 PurE2_6.5 and Estuary, when I enable Picons, the channel name disappears from the Channel List. Only the picon is shown. How can the channel name and picon be shown together, pl? thks.

Hi satfoot

I had the same problem, here is my solution

Go to MENU -> SETUP -> SYSTEM -> CHANNEL SELECTION SETTINGS

On 3th page set SHOW COLUMNS to 375 pixels wide

This work for me. You can change the pixel wide as suit you.

Hi

I have a Octagon SF4008, and I would like have, SDG 8.0, OpenATV 6.4 and PurE2 6.5 in multi-boot.

Is NeoBoot 8.24 by gutosie the right solution?

Or can you recommend any other solution?

Which image should be in Flash?

Regards

Iradj

Quote from gorski

There are different ways of adding shared folders from various devices to Kodi...

Which did you try?

I got it to work.

You must mount the share under root. It works fine with small files but, 2160P HDR blue ray rip crash it, I think it is because my receiver (SF4004) is not powerful enough.

Thanks deanpez

The issue is not the resolution.

I find out the issue is because my video files are on the NAS , Kodi plays fine local files.

Hi

I’m using the latest image on my Octagon SF4008, I installed Kodi 18, and it starat fine , BUT when I try to play any video, the player start and then noting happen no video(black screen) no audio.

Any suggestion what can help?

PS: I have exactly same issue what all other images.

Hi firmmino

I had the same problem, here is my solution

Go to MENU -> SETUP -> SYSTEM -> CHANNEL SELECTION SETTINGS

On 3th page set SHOW COLUMNS to 375 pixels wide

This work for me. You can change the pixel wide as suit you.

Is there any plan for Octagon SF4008 OpenPLI Official Support?

Hi

Is there an image for OCTAGON SF4008 ?

Regards

Iradj

Thank you master G :thumbup:

Thank you carloscarlosa

But I want to try this version (3.2).

I just need someone tell med which file for SatDremGR 5.0 image on Octagon SF4008?

Regards

Iradj

Hi

Which file for SatDremGR 5.0 image on Octagon SF4008 ?

I tried “ enigma2-plugin-softcams-ncam-all-images-osdreamox-arm-open-source_V3.2-r0_all.ipk” but is does not work

Regards

Iradj

Hi

I need some help, I installed the “enigma2-plugin-extensions-e2m3u2bouquet_0.6_all.ipk”

My provider do not appear in the list of provider, how can I add my provider to the list ?

Thanks for your help

Regards

Iradj

Hi

will my installation; 2 receivers control their own motorized satellite dish with single cable ever work?

Is there any hardware or software that will help?

Any suggestions that I should try?

Regards

Iradj

Hi

I need some help, her is my situation:

I have 2 Motorized (STAB HH120) satellites dishes

Each dish has a Inverto IDLU-32UL40-UNBOO-OPP Unicable II LNB

These 2 LNB are connected to Unicable II 2-way Combiner IDLU-UCM1O1-OOO2O-OPP

From there a single cable goes to 2 receivers (Octagon SF4008 and VU+ SoloSE2) using OpenATV 6.0 image

I have also added a Unicable II Power Inserter, IDLU-PINS02-OOOOO-OPP between combiner and receivers

I have tested one dish alone, everything work fine without the 2-way Combiner IDLU-UCM1O1-OOO2O-OPP .

I tried different combinations without any result no signal at all

The question is how do I configure the tuner each receiver control their own satellite dish.

Here is what I can change :

Tuner A

Configuration Mode: Advanced

Satelitte : All Satelites

LNB: LNB 1

Priority : AUTO

LOF: UNICABLE/JESS

Unicable Configuration mode: Unicable LNB

Manufacture: Invereto

Type: IDLU-32UL40-UNBOO-OPP

Channel - SCR1
Frequency – 1210

Tuning algorithm: reliable

Fast DiSEqC: None

Toneburst : None

DiSEqC 1.0 Command: None

DiSEqC 1.1 Command: None

Sequence repeat: No

Longitude xxx.yyy East/West

Latitude xxx.yyy North/South

Kind regards

Iradj

Hi

If anyone is interested I find this device Unicable II Power Inserter, 5-2400MHz ( IDLU-PINS02-OOOOO-OPP)   At this German Web Shop https://www.satshop-heilbronn.…-inkl-Netzteil-5-2400-MHz and order One.

I hope this device will solve my problem.

Kind regards

Iradj

Hi

Recently I replace my universal LNB with Inverto Unicable II LNB (IDLU-32UL40-UNBOO-OPP)

Using with my motorized dish STAB HH120 Rotor and my new receiver Octagon SF4008, openATV 6.0 latest OScam/Ncam

There is a very long cable from the LNB to the receiver that cannot be changed.

The problem is that the with with Inverto Unicable II LNB the rotor cannot tune to different satellite most of the time.

It looks like that there is not enough power supply to the rotor, and I must use a power inserter.

I cannot find any satellite power inserter web shope based any place in Europe.

Can anyone send me a link to a Web shop where I can purchase a power inserter in Europe?

or any other advice to solve my problem?

Kind regards

Iradj

Thanks Pippop73, it's work:)

I tried it on OpenATV 6.0 image too, and it doesn’t work

Hi

I tried both “ncam.cortexa9hf-vfp-neon “ and “ncam-libusb.cortexa9hf-vfp-neon” on my Octagon SF4008 with OpenVix 5 image and it doesn’t work I had to go back to 1.1 version

I rename it to “ncam” FTP to /usr/softcams , change the attribute to 755 and restart the ncam.

Is there anything else I must do?

Regards

Iradj