Dears,
I am a newbie , please explain to me ,
what is MultiCS?
What are the capabilities of MultiCS?
Is it used to built commercial CS servers?
Is there a wiki available for MultiCS?
Thanks in advance,
:)
Dears,
I am a newbie , please explain to me ,
what is MultiCS?
What are the capabilities of MultiCS?
Is it used to built commercial CS servers?
Is there a wiki available for MultiCS?
Thanks in advance,
:)
S3n0 Thank You!!:smiling:
Dears,
I have 3 Linux boxes and one Cline at my home;
If I share the C line with OSCAM with 3 Linux receivers ; would the CCCAM server detects the additional 'sharing' of the Cline and disconnect or 'blacklist' the Cline?
i.e. Receiver 1 shares Cline with Receiver 2 & 3
Please advise,
:eye roll:
Dears,
Can you please guide me to config MGCAM line on Mut@nt HD51 Open ATV 6.3 image?
I could not find the MGCAM config file locations in my receiver.
:eye roll::rasta2bigsmoke0gf1:
Master G Thank you!
The Panel Works!
I see!
I am using [openatv-6.2-mutant51-20190615_usb.zip]
But check below from ATV forum;
Dears,
Can you please post the latest OSCAM EMU ipk for Mutant HD51 with openATV image?
I tried below but it dose not install!
enigma2-softcams-oscam-all-images_11.523-emu-r796-arm+mips_all.ipk
:unhappy:
Thank You!
I got below MGCam line similar as below;
server
port
user
pass word
Deskey:01 02 03 04 05 06 07 08 09 10 11 12 13 14
Can you please post the config procedures to add MGcam line in to HD51?:smiling:
:crying:
No reply?
Master G,
My receiver is Mutant HD51 with Open ATV and I have installed MGCamd 1.45a [enigma2-plugin-softcams-linuxsat-mgcamd-1.45a_openatv_mips32el.ipk]
I got below MGCam line similar as below;
server
port
user
pass word
Deskey:01 02 03 04 05 06 07 08 09 10 11 12 13 14
Can you please guide me to config my receiver for above MGCam lines?
Please find the attached image.
is there a web interface available with MGCamd?
or can I config OSCAM for MGCamd?
Please advise,
Thanks
:) Thanks!
Fixed system, I need to install several KU dishes with my Receiver (multi feed)
Mika,
One more clarification please;
I am using Mutand HD51 with OpenATV and only available DiSEqc 1.0,DiSEqc1.1 and DiSEqc 1.2.
DiSEqc 2.1 is ok with my receivers?
Dears ,
Can you please post a list of DiSEqc 1, 1,1 and 1.2 switches brands which recommended for E2 boxes ?
I have tried with DiSEqc 3 but did not 'work' with Mutant HD 51.
Try Open PLi image, comes with various sofcams
Hi Master G,
Installed on Mutant HD 51/ Open ATV using telnet and it runs without any issue.
Thank you!:D:):):)
Master G
Thank you!!
:):):)
Master G,
My silly mistake !
Can you please clear my doubts below ?
# Can we install only the 'OSCAM EMU' or we have to install the default (PLi6) OSCAM first and then install OSCAM EMU?
# i am trying to open V*i*d*ieo**guard NDS service on S*T8*8E with this EMU is there any additional bin file or setting needed for that?;););););););)
Thanks in advance,
Master G,
I ran the command and i got the attached errors ,but ipk file is visible on the 'temp' folder.
please refer to the attached,
Master G,
It did not installed any guidance please