Posts by neil306

  • Need viasat configs for oscam on vu solo2

    have you tried this config which can be found in the oscam configs for all cards section make sure you put card in bottom slot for dev/sci0 or change to top slot with dev/sci1 for solo 2
    ####oscam.conf####


    global]
    nice = -1
    logfile = /dev/null
    clienttimeout = 5000
    fallbacktimeout = 2500
    clientmaxidle = 120
    cachedelay = 120
    bindwait = 120
    resolvedelay = 30
    serialreadertimeout = 1500
    maxlogsize = 10
    waitforcards = 1
    preferlocalcards = 1
    saveinithistory = 1
    keepalive = 1


    [dvbapi]
    enabled = 1
    user = linuxsatsupport
    boxtype = dreambox
    au = 1
    pmt_mode = 0


    [cccam]
    port = 12000
    version = 2.1.3
    build = 3165
    reshare = 1


    [webif]
    httpport = 8888
    httpuser =
    httppwd =
    httprefresh = 5
    httphideidleclients = 0
    httpallowed = 192.168.0.0 - 255.255.255.255
    debug = 255


    [monitor]
    appendchaninfo = 1


    ####oscam.server####


    [reader]
    label = VIASAT
    protocol = internal
    detect = cd
    device = /dev/sci0
    caid = 093E
    ident = 093E:000000
    EMMCache = 1,1,2
    blockemm-unknown = 1
    blockemm-u = 1
    blockemm-g = 1
    group = 1



    [reader]
    label = remote
    protocol = cccam
    device = peers.dyndns.org,12000
    account = user,pass
    group = 1
    caid = 093E
    ident = 093E:000000
    cccversion = 2.1.4
    reconnecttimeout = 5


    ####oscam.user####


    [account]
    user = linuxsatsupport
    group = 1
    caid = 093E
    ident = 093E:000000
    au = VIASAT
    monlevel = 0


    [account]
    user =
    pwd =
    group = 1
    caid = 093E
    ident = 093E:000000
    cccreshare = 1
    cccmaxhops = 2

  • Positioner set up

    Sounds like your dish is out, not set up properly. If you are using usals your motor will always go back to the position you set your co-ordinates up to regardless of whether you fine tune it. If you use advanced set up in tuner configuration change settings to, lnb1, diseqc 1.2, use usals no, save satellite no. to .... I use 28 for 28.2e, 23 for 23.5e, 13 for 13e, 5 for 4.8e, 1 for 0.8w, there is no need to change any other settings then press ok to save changes. Then go to positioner set up and start at thor 0.8w and fine tune to best signal and save position as previously mentioned 1. Then do a search east for say 4.8e and it should stop on that satellite then fine tune again for best signal and save to 5..do this for all satellites if you can find them, make sure when you search you use a valid transponder or you wont find anything. This is only a quick fix, if you cannot find thor I am 99% sure your dish is not lined up or set up correctly the arc is incorrect. Hope this helps you

  • How to connect oscam with cccam?



    you need to ftp the files the 3 files.. oscam.conf oscam.server and oscam.user files to etc. tuxbox... config, then restart oscam


    oscam.conf


    [global]
    nice = -1
    logfile = /var/log/oscam.log
    clienttimeout = 5000
    fallbacktimeout = 2500
    clientmaxidle = 120
    cachedelay = 120
    bindwait = 120
    resolvedelay = 30
    serialreadertimeout = 1500
    maxlogsize = 10
    waitforcards = 1
    preferlocalcards = 1
    saveinithistory = 1
    keepalive = 1



    [dvbapi]
    enabled = 1
    au = 1
    pmt_mode = 0
    delayer = 60
    ecminfo_type = 1
    user = linuxsatsupport
    read_sdt = 1
    write_sdt_prov = 1
    extended_cw_api = 2
    boxtype = dreambox


    [webif]
    httpport = 8888
    httptpl = /etc/tuxbox/config/tpl/
    httprefresh = 15
    httpshowmeminfo = 1
    httpshowuserinfo = 1
    httpshowcacheexinfo = 1
    httpshowecminfo = 1
    httpshowloadinfo = 1
    httpallowed = 192.168.0.0-255.255.255.255,127.0.0.1
    http_status_log = 1


    oscam.server


    [reader]
    label = myserver.dyndns.com
    protocol = cccam
    device = myserver.dyndns.com,10000
    user = user
    password = password
    inactivitytimeout = 30
    group = 1
    emmcache = 1,3,2
    cccversion = 2.1.3
    cccmaxhops = 1
    ccckeepalive = 1
    cccreshare = 1


    oscam.user


    [account]
    user = linuxsatsupport
    group = 1
    au = myserver.dyndns.com

  • install avermedia c127 drivers ubuntu 15.04

    I have just installed ubuntu 15.04 and I am in need of avermedia game broadcaster hd c127 drivers as ubuntu doesn’t see my capture card.
    I have scoured the net for these with no luck and also looked on avermedia web site but linux is not supported.
    Wndows sees the capture card fine so it is working ok
    Can anybody point me in the right direction to install these
    thanks to all
    neil306

  • mag254

    Load your m3u file onto a usb drive and insert into mag254
    Go onto settings, then select the inner portal then select media, you should see your usb drive in a list select it
    You will be given options on bottom of the screen ... the colored buttons on the remote control
    it really is as simple as that