NCam for Spark

Don t work

Ncam1.7 sh4-spark file. For alternative softcam manager.

First install alternativesoftcammanager_20140213-r2_sh4.ipk

FTP over NCAM17.sh4 to / usr / bin / cam. Restart GUI.

FTP Ncam config files and softcam to / usr / keys.

Hi Wika,

I am booting my spark / enigma alien in enigma mode. Are the above only to be used when booting to spark. Do I need a different Ncam for running in enigma2.

Thanks in advance.

Thanks for that.

I will give it a go. Keep you posted.

Had a go but cannot even browse to ncam using webif. I installed ncam in usr/bin/cam and renamed it to ncam and set to 755.

I put all my original oscam configs in var/keys and renamed to ncam.cfg etc, etc.. I removed my original SH4 oscam. Any Ideas. I am using the alternativesoftcammanager to start ncam. Maybe I have not installed correctly. Ncam installed is V1.7r5.

UPDATE.

Tried 1.1-linuxsat mips32el.ipk. Still the same. I cannot browse to see if ncam is working or installed correctly.

Hi..

You must use the ncam version in the first entry. Other ncam versions do not work.

Follow the explanation.

Softcam Manager will be installed and available in plugins.

I use it daily on my shd8900

Quote from hs5424

Hi Wika,

I am booting my spark / enigma alien in enigma mode. Are the above only to be used when booting to spark. Do I need a different Ncam for running in enigma2.

Thanks in advance.

In enigma2

Thanks for that.

Will post outcome.

Update.

Installed 1.5 spark form first entry, renamed it ncam and set 755. My configs are in var keys and I renamed them all to ncam.xxx etc.

Still cant web browse using ip:8181. My box is alien mini chip 7111 and running Vix 4.

Mystery.

You must install ncam from my first entry, Ncam1.7.sh4.

These two downloads belong together

You do not have to rename it, just 755.

OK. I thought you were referring to the post at the top of the page.

Cheers.

Hi wika,

Sent Ncam1.7sh4 to / usr / bin / cam and set 755. Went to alternativesoftcamanager and pressed start but I still cannot see ncam running with the web interface eg, 192.168.1.10:8181. I checked the port in my ncam.conf

Quote from hs5424

Update.

Installed 1.5 spark form first entry, renamed it ncam and set 755. My configs are in var keys and I renamed them all to ncam.xxx etc.

Still cant web browse using ip:8181. My box is alien mini chip 7111 and running Vix 4.

Mystery.

I have not tried Vix imaget with alternative softcam manager, I have tried out on OpevATV, OpenESI and OpenPLI

Try OpenESI 5.0 for Spark. I think it's best to Spark off the images I've tried

OK.

My main aim is to run my Meo card in the alien and feed to my other stb's using cccam. For some reason Oscam was opening the meo channels but was very hit and miss when I sent to cccam so I was following advise from another forum member and was going to see how Ncam would work as a reader.

I will only be using the alien as a card reader so I am open to suggestions as to what image I will boot to. I have never heard of OpenESI but am willing to give it a go.

UPDATE,

I re-flashed the alien with Openatv and managed to install Ncam 1.1. However it is behaving in the same way as oscam was in vix. My client receivers running cccam clear pictures and after about 20 seconds they freeze. If I change channels the picture will return for another 20 seconds or so. It seems to only get 1 ecm from cccam.

Any ideas anyone.

good morning , as i have movistar card and get the same prob with amiko alien but with the same conf n cam on vusolo and vu solo2 not prob

????????????????????