How can I use this new 1.4 official version in newly flashed Image, which have no Cam install, because the file ( official ) only is Ncam.mips, a brief explanation is appreciated , it guide me also other members to use these file
Ncam on Enigma2 STB
-
- NCam Support
- Rizwan77
- Thread is marked as Resolved.
-
-
For enigma 2 easiest way is manual install (copy ncam.ipk to /temp and gave atribute 755), then from software menagment go install local extension. You can also simply copy ncam. mips and create start script but thats depends on image which you use
-
official ncam 1.4-r0 has no ipk version. Actual ipk versions are fake versions
-
Look at this. for ipk.
-
For enigma 2 easiest way is manual install (copy ncam.ipk to /temp and gave atribute 755), then from software menagment go install local extension. You can also simply copy ncam. mips and create start script but thats depends on image which you use
There is no such file Ncan.ipk in original version, point is its newly flashed box with no cam installed, so, nothing replace with new ncam.mips
-
I am still finding a procedure, how to install original version in enigma2 STB, any solid example ?
-
I am still finding a procedure, how to install original version in enigma2 STB, any solid example ?
Which receiver and image ?
-
I have solo2, Openpli, no cam at the moment, want to try Ncam latest original
-
Download NCam-1.4-r0 (Oficial)
Extract the attachment.
The version for vuplus solo2 is ncam.mips.
Connect to the solo2 with an FTP tool and go to /usr/bin folder.
Send ncam.mips to this folder.
Rename ncam.mips to ncam.
Change permissions on ncam to 755.
FTP to /etc/init.d
Send attached softcam.ncam to this folder.
Change permissions on softcam.ncam to 644.
Send ncam configs to /etc/tuxbox/config/ncam.
Reboot the solo2.
The attached softcam.ncam will only work for openpli and satdreamgr image.
-
master G !
Thank you for explaining, I perform as you said, also copy config folder in tuxbox,Ncam showing in Softcam setup put a working server in it, but nothing happen, same line working with Cccam
-
Send ncam configs to /etc/tuxbox/config/ncam.
-
its already in etc/tuxbox/ncam, also not showing with webinf, not sure its working or not
-
/etc/tuxbox/config/ncam.
-
sorry for written wrong, its already in etc/tuxbox/config/ncam
-
I think cam is not starting, there is some step missing, other than putting ncam.mips ( after rename to ncam) in usr/bin
-
Quote
FTP to /etc/init.d
Send attached softcam.ncam to this folder.
Change permissions on softcam.ncam to 644.
as i remember the script file also need 755 attributes...
-
Check ncam is working by going to the NCAM Admin Control panel in a browser http://ip.of.solo2:8181
Once in the panel go to configuration then DVB-api.
Check the box Write detected prov name to srvid and save.
Don`t restart NCAM, after a restart it doesn`t save and you need to recheck this box again.
-
As I post earlier, webinf not working on Ncam, so I assume, its not working
-
What happens when you try to start it in telnet ?
/usr/bin/ncam
-
not in telenet, just check through browser, it says page not found
NCam Support Forum
Configs, discussion, downloads and guides for NCam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!