FreeCccam 1.9 ofline
Number 8 to setup; u have : oscam on_off u have to put it on. IDEM for Ncam Cccam and Gcam.
FreeCccam 1.9 ofline
Number 8 to setup; u have : oscam on_off u have to put it on. IDEM for Ncam Cccam and Gcam.
I installed the plugin 1.9 after a reflash on Amiko Alien (OpenATV) cause there were problems with ipk install ( same as on ZgemmaSH2) , now it's ok but i have a question: at ip config which one it should be , router ip or box ip?....Many thanks for your brilliant work!
Port ... Emu in gcam.config....oscam.config......ncam.config
Ip ..... box
Tested on vu+ ultimo 4K and gigablue quad plus both with openatv 6.2 Not working for me.
Free cccam Plugin 1.9 freeze
Tested on Octagon SF4008 4K with openatv 6.2.
Not working.
Enigma2 FreeCccam Plugin By Aime_Jeux 1.9 freeze.
Return to version 1.8
Mistake - a double post
not workink on my vu+ zero blackhole 3.05
not workink on my vu+ zero blackhole 3.05
I tested it on blh 3.0.5 and it works
not workink on my vu+ zero blackho
Number 8 to setup; u have : oscam on_off u have to put it on. IDEM for Ncam Cccam and Gcam.
not workink on my vu+ zero blackho
Number 8 to setup; u have : oscam on_off u have to put it on. IDEM for Ncam Cccam and Gcam.
verify the address of your oscam.server file
just a note go through mandatory configuration panel
yes
ip = box
port = oscam & ncam & gcam
thank you aime_jeux great plugin,work finr with no freeze on my dm 800 hd bh3.0.4 ncam :thumbup:
many thanx for all work and plugin:thumbup:
if there is no crash file I can not tell you anything
excuse me
fantastic work .brother
version 1.19 works perfect on Optibox m7 runing openhdf 6.2
very very good plugin thank you
Non va bene sul mio Xtrend et 8000 immagine openatv 6.2. Grazie.
Hello, it's very slow on my Edision Os Mini + with OpenATV 6.2
More than 5 minuts before the 1st (no working) plugin screen (still loading)
Launched the plugin at 09:48, the 1st screen appeared at 09:53
After more than 10 minutes still loading (10:08) and nothing can be done ("exit" work)
10:58 Update
still loading
I can see:
the left is blank, the "spinner" still active , on the lower portion I can see (red) [Cccam] (green)[Gcam]..and "OK to choose server" "Key Help or Info" "Number 8 to Setup".
the right only contains "s1.satuniverse.tv" / on bottom side "OK to Remove Server"" "Auto Update Not Activated"
"Exit" worked after a couple of minutes
Thanks
-------------------------------------------
The problem was the default IP automatically generated by FREECCCAM in the configuration 192.168.1.0
once replaced it with the right one (in my setup is 192.168.0.1) all works perfectly
Display MoreHello, it's very slow on my Edision Os Mini + with OpenATV 6.2
More than 5 minuts before the 1st (no working) plugin screen (still loading)
Launched the plugin at 09:48, the 1st screen appeared at 09:53
After more than 10 minutes still loading (10:08) and nothing can be done ("exit" work)
10:58 Update
still loading
I can see:
the left is blank, the "spinner" still active , on the lower portion I can see (red) [Cccam] (green)[Gcam]..and "OK to choose server" "Key Help or Info" "Number 8 to Setup".
the right only contains "s1.satuniverse.tv" / on bottom side "OK to Remove Server"" "Auto Update Not Activated"
"Exit" worked after a couple of minutes
Thanks
Same with me on Octagon SF4008 4k and OpenATV 6.2
ps.
big thanks for your Aime_Jeux work on the plugin
Don’t have an account yet? Register yourself now and be a part of our community!